• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

A big thanks to all members past and present for making the club viable for so long.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Front suspension

Started by foggy, 06, June, 2010, 09:35:22 PM

Previous topic - Next topic

foggy

Since I bought my Robin Hood S7 (I don't know the history of the car) I have never really been happy with the front suspension, or the lack of it, its the model with the springs/damper inside the nose cone. So today I took it all apart, when I jacked the car up, the front wheels did not drop, as I expected them too, I put some axel stands under neath the front of the car and jacked the wheels up individually,the front suspension did not compress and all I did was to jack the car up. I stripped the whole lot out to make sure that nothing was bent  or broken,which it is'nt.I turned my attention to the spring/damper, took the spring off,to see if I could compress the damper,to see if that was'nt damaged or seized,which it is'nt,but did notice the spring adjusters was fairly tight  and wound up, this might have been done for the track. Does any one know how much  up and down movement should I have on this model? Or is it mean't to be like this?  Any help would be greatly appreciated.

'The Gaffer'

Sounds odd theres no movement at all, could you just experiment with the spring settings?

foggy

Yeah, I think this is my only option,but not sure how much movement I should have.

Bulldog Bri

I've got at least a couple of inches of movement in the shocks on my Locost, if that helps.

8)

'The Gaffer'

Quote from: foggy on 06, June, 2010, 10:26:01 PM
Yeah, I think this is my only option,but not sure how much movement I should have.

I would just adjust till it suits you, I have less than 1/4 inch of travel if I use jack under the front wishbones. I only have a light bike engine in there too. Needless to say my suspension is very hard. Example, if I am accelerating and I go over rough ground my foot will jump off and on the accelerator pedal because of the buffeting.

If you want softer, just adjust till it feels right for your driving style. Personally, I like it hard :)

Quarrycars

I would back off all spring and damper adjustments to their softest setting then progressively stiffen the settings until you find the best compromise.  Remember the tires are also part of the suspension, maybe the main part with very stiff settings!

foggy

Done what was suggested, unscrewed the spring tensioner,finally got some movement by jacking the wheels up and lowering them back down. I unsrewd the tensioners by 2 inches on each side,which I think is a lot, no wonder they did not move before. I have asked my mate who is a engineer to take the top suspension arms into work and to make sure they are straight,they look good with the naked eye, but seeing they have be taking a lot of pressure, ie pot holes etc, I want to make sure before I put them back together again.

'The Gaffer'

I think a lot of things are 'by eye' on a kit car. I would just bolt it up and try it :)

Nothing wrong with having them checked over though.

'Mendip Wurzel'

I'm presuming that the ground clearance will get less as you adjust, or is it that solid. I adjust my springs to suit the ground clearance which I don't like much less than about 3 inches as you obviously start hitting manholes and things. I would want to be seeing some sort of change in the ground clearance as I adjust the springs.
Tyre pressure is usually fairly soft on lightweight kitcars (ie 18 to 20psi). 

Camber Dave

Unless you have manufacturers set up info do this. Wind the damper adjuster knobs fully anti clockwise to fully soften them.
Adjust the spring platforms down until the lower wishbones are about 10mm higher at the centre of the chassis bush than the centre of the ball joint (2mm below the bottom of the gaiter).
Set the spring platforms the same height as each other.
Check the ground clearance under the sump ect - 85mm will clear sleeping policemen- raise ride height if necessary.
Measure the ride height under the front of the chassis at axle centre line.
Set the rear ride height 20 - 25 mm higher.  Then wind up the drivers side spring platform up 5mm higher to allow for the drivers weight.
Set damper 1/3 of the range ( 4 of 13 for Protech 12 of 42 Gaz ect) and plus 1 ckick on the rear.
Reset them on the road to suit your comfort/ response preference.
The get the corner weights checked.

'Mendip Wurzel'

Interesting what you say Camber Dave..

I've got my Gaz damper set about half way (approx 20 clicks), I think I may alter this down to about 12 based on what you are saying.

Thanks

foggy

Thanks for all the information.Front tyre pressure is about 20 psi (it was 30). Good tip about a little bit stiffer on driver side, I would'nt have thought of that. One of the suspension arms was out of true, had that problem sorted out, got most of it back together. Rear suspension,non adjustable. Now got movement on the front suspension, suspect I will have to stiffen it up a little bit,as it is wound all the way down at the moment. Damper setting on No 4, got to check sump clearance, damper setting was set at maximum hardness. The suspension was'nt  moveing at all. One more thing-- I think its called, camber- with a piece of wood on the edge of the tyres,a spirit level vertical,with the bubble  in the middle of its run, what would be the ideal measurement between the piece of wood and the straight spirit level? If any one knows, in inches please (Robin Hood S7) early model--cheers

'Mendip Wurzel'

I am sure someone will give you a much better reply the me as I haven't really got a clue other than you don't want the wheels leaning out as this is apparently rubbish for handling. As far as I am  aware you need them levelish, or leaning in by a few degrees.

foggy

When you say leaning in by degrees, how do you measure degrees?

Quarrycars

As a rough guide; 1 degree @ 30 inches is about half an inch

Camber Dave

To set camber first check that your ride height. Then put put the spirit level on a transverse chassis member and make sure the car is level. Pack up the low side with plywood pieces under the wheels.

We normally set the camber at between 1/2 and 1 deg Negative ie wheel leaning in at the top. It is more important to get them equal than the actual angle.

Put a piece of wood against the tyre away from the bulge at the bottom.

If your wood is 3 inches in front or behind the centre of the wheel it will be touch the tyre about 17 inches (440mm) apart and 1/2 a degree will be 5/16 in ( 4mm) gap to the tyre. 1deg will be (8mm) A drill bit or rod is easier to juggle than a steel rule.
Normally changing the camber will alter the tracking.


foggy

Thanks for all the help, especially Dave. Followed your  advice as best I could. Got both wheels at the same angle now (won't get the exactally the same, as I have to do full turns to get the adjustment, but its very close and I am hapy with that. The suspension is working brilliantly, maybe a tadge soft, but I am going to run with it. The car is slightly lower than what it was, I got just under three inches from the sump guard to the road. I will have to go very carefully over speed humps. I will get the tracking done, as you say the tracking will now be out.Just got to get the bonnet resprayed, going to get the paint matched in a few weeks time when  I am off work. I think it was Phil who said that when he got time and I got the paint,he would do it for me.  Thanks once again.

'The Gaffer'

#17
Get your name down for the corner weight clinic :) Its possible Dave can do your tracking at the same time?? Even if he cant the clinic will have your car suspension set up well.

Failing that speak to Lee at FCM Motorsport, he will do a great job.

FCM Motorsport
Unit 1
Netham View Industrial Park
Netham Road
BS5 9PQ

Tel & Fax: 0117 941 3232

Email:enquiries@fcmmotorsport.co.uk

foggy

spoke to lee he going to set the steering up on saterday ie tracking etc  i have done the best i can there is  still  something not  quite right i'm  sure  he will sort it out ;

foggy

So off down to FCM Motorsport, previously told Lee that this would not be a five minute job,because of the set up, see previous posted pictures. Up it went up on the ramp,off came the front wheels again,after a little bit of tinckling and his laser tracking and camber machine, what I thought was very close to my settings,found out that I was was way out.He sorted all that out, but it did take the best part of two hours to do it. What a difference he has made and very reasonably priced. The car now drives supurbly and if any one has similiar problems go and see Lee, he certainly knows his stuff-well impressed.

'The Gaffer'

Quote from: foggy on 26, June, 2010, 12:14:07 PM
So off down to FCM Motorsport, previously told Lee that this would not be a five minute job,because of the set up, see previous posted pictures. Up it went up on the ramp,off came the front wheels again,after a little bit of tinckling and his laser tracking and camber machine, what I thought was very close to my settings,found out that I was was way out.He sorted all that out, but it did take the best part of two hours to do it. What a difference he has made and very reasonably priced. The car now drives supurbly and if any one has similiar problems go and see Lee, he certainly knows his stuff-well impressed.

Excellent news. Lee really is good :)

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=