• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

A big thanks to all members past and present for making the club viable for so long.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Getting hot - does water wetter work?

Started by Grin-a-lot, 03, July, 2011, 03:39:51 PM

Previous topic - Next topic

Grin-a-lot

My car tends to run at about 90+ degC and after about 10 laps of Llandow was overheating.  This is with an oil cooler fitted behind the radiator.  Thermostat is working fine and fan spinning in the right direction!

My cunning plan (to improve things ready for Donington) is:

Move fan from front of rad to back as where it is can block airflow it seems.

Flush radiator again to clean out the remaining cr*p, lots of brown gunk still evident

If I can find room move oil cooler infront of rad.

Install temperature sender in oil line to see what the oil temp is actually doing.

Install some ducting so oil cooler gets a nice blast of cold air

Add water wetter to the coolant.  But the big question is - does it actually make a difference or is it just marketing hype?

Also are there any top tips for refilling with water to avoid airlocks or anything else I should consider?

Splits

Hi
I used water wetter in my autograss race car, and it did help with keeping cooler.

dikkie

Simple things but:

Have you checked for any cold spots on the radiator? the gunk could be cutting off some of the channels...

is the rad cap holding it's pressure ok?

Grin-a-lot

Checked all hoses are hot but not checked rad cores themselves.

The system doesn't seem to be pressurising too badly, plenty of return from top of thermostat housing to expansion tank as well so flow seems ok.  I'm pinning my hopes on a good flushing first of all.

Quarrycars

I hadn't heard of wetting agent since the days of using it in photographic chemicals in the darkroom, but using it in the cooling system makes sense.  I've always used Bars Leaks in cooling systems, as it contains soluble oil I guess it is also a wetting agent.

Regarding the cooling fan, behind the rad is probably better but make sure it is turned off at speed, over about 50 mph the spinning fan restricts airflow, OE electric fans usually do this automatically.  Also check that all the airflow is going through the radiators and not bypassing them via gaps and that there is low pressure behind them with good paths for the heat to escape.

If the rad cap is in good shape a 15 psi system should not boil till about 130 deg, on most modern cars the temp guage stays in the center until about 112 deg, hot is about 118 and overheat is 122.  I try not to run above 110.

Denzle

From what you are saying, your first step would be to take off the rad and have it proffesionally cleaned out.

The slightest coating of crud inside the tubes can make a lot of difference.  When you are one hundred percent certain that the rads ok, then move onto something else if its not solved the problem.
                                      Denzle... ;)

tony.g

Do a block test to make sure your head gasket's not leaking slightly.
Block tester kits are cheap enough on Ebay.

YZFMINI

just to say something different to everyone else.
Are you sure the fuel mixture is not running to lean anywhere in the rev range as this with warm it up nicley.!!!

Grin-a-lot

QuoteAre you sure the fuel mixture is not running to lean anywhere in the rev range as this with warm it up nicley.!!!

That's interesting, my carbs are spitting back a bit recently which I gather is a sign of running lean.  I'm planning on pulling the plugs to have a look when I get home tomorrow.

YZFMINI

Yep your right spitting back is a sign of weak mixture..

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=