• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

Due to 100's of daily spam registrations, new member applications have been disabled. Sorry.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Rusty nuts and bolts - Summary of what I've learnt

Started by Richard, 23, July, 2009, 10:07:25 AM

Previous topic - Next topic

Richard

Rusty nuts / bolts, I think these things are a curse as described elsewhere, however, we'll all come across them at some point so here is what I've learnt and yet again I suspect you all know this already but this seems to be the order of most efficient approach assuming you don't grab the angle grinder to start with;  ;D
•   Clean off nut/bolt, wire brush useful, also found old screwdriver could cut a cleaner flatter surface when nudged with hammer.
•   Penetrative spray – I have a specific penetrative spray which seemed to work well GT85, am sure others available, also have WD40 but did not seem quite as good for this purpose, could be imagination.
•   Use correct size socket/ spanner and have first attempt at undoing, must keep that socket on the nut/bolt squarely.
•   Then try to just a very little tighten it before undoing, you are from now on more or less trying to break the bond that has occurred over time between the bolt / nut and there surroundings.
•   Longer lever can be very useful here, I now have a 2 foot breaker bar, soo much more leverage than the socket set 9" I had to start with, sorry metric these days should be 600mm and 230mm or something else that most people seem to convert back to inches to mean anything.
•   Still stubborn ? then heat time, get blow torch (I had one from fitting a few copper pipes some years ago (Sorry Dave not encroaching on your business honestly ;) ), heat that nut / bolt to a very shiny orange red, not the reddish purple you get on very hot exhausts. Careful it is very hot and be very aware about what else is nearby.
•   Drilling out the bolt becomes an option, given how hard they can be I found this ineffective but in some circumstances I can see how it would be best e.g. drill out , cut new thread and refit new bolt.
•   ANGLE GRINDER, Still stubborn ? then knowing nothing else it was angle grinder time, now this depends on the bolt type / thread nut etc. whether this works or is right thing to do.
        o   First technique I now go for is cut off part of nut so you just skim the bolt, then with hole punch and hammer knock the nut round the thread, seems quite effective, use that spray stuff.
        o   Then next option is chop off nut and or / bolt head and use nail punch to knock it out (does not work obviously on threaded bolts.
        o   Next option if you suspect threaded bolt and the bolt is big enough, cut down centre of nut end of bolt, squeeze the two halves into each other, more spray and undo bolt as normal (much lessthread stuck to inside of thread).

Any other tips warmly welcomed !

No I wasn't thinking about Lorry's for those that spotted it  ;)

dave_bence

Excellent post Richard!

Having stripped a rusty 13 year old Sierra and an even rustier 14 year old Metro, I've used most of  the methods you've described.

Just to add a couple of tips:

If possible, use 6-point "flank drive" sockets - they're much less likely to slip than 12 point sockets.

The best penetrating fluid I've used is PlusGas. Hard to find but worth tracking down.

Before heating a stubborn bolt, I give it plenty of whacks with a hammer - this seems to help break the "bond". Make sure you hit the head of the bolt square on - you don't want to deform the head which would cause even more problems!




'The Gaffer'

#2
Only thing I would add to your arsenal would be a small oxy-acetylene kit.

This allows you to add heat to the nut quickly without the bolt having time to expand as well.

You can also use to cut things up  ;D

EDIT: Forgot to memtion the trusty air impact wrench and a set of impact sockets.

Quarrycars

I am showing my age here, but before Japenese cars came along the main use for a 12mm socket was to drive it on to a rusted 1/2in nut.  The technique of using the next size down on very rusted nuts probaly still works (I've worked the last 30 years in California and Arizona where we don't have rust!)

Hairy Santa

you can also buy a nut splitter,

but if you havn't one a decent sharp chisel struck onto the flat of the nut normally works - dont forget to dolly up the other side of the nut if possible with another hammer or a lump of steel

this way you can 99% save the bolt for reuse

YellaBelly

Only thing I can add that hasn't already been said, if you're using the 'appliance of science' (i.e. hit the bu**er hard', make sure that you aren't going to break/fracture/crack etc. any castings especially if we're talking alloy. (Don't ask me how I know :( )

JB

'The Gaffer'

Quote from: YellaBelly on 11, February, 2010, 09:40:55 AM
(i.e. hit the bu**er hard', make sure that you aren't going to break/fracture/crack etc. any castings especially if we're talking alloy. (Don't ask me how I know :( )

That also applies to fingers :D

YellaBelly


'Mendip Wurzel'

#8
If the nut is large enough I have welded bars onto the side of it for leverage ...

paintman

I'm good at cutting things off......I cut off an index finger last year with a 8" power saw!! :P

Bulldog Bri


'The Gaffer'

Quote from: paintman on 12, February, 2010, 01:13:45 AM
I'm good at cutting things off......I cut off an index finger last year with a 8" power saw!! :P

Ouch :o Did they manage to sew it back on again?

paintman

Yes luckily. They managed to join up the nerves and tendon and set the bone ok but the blade went though the knuckle which b*llsed it up somewhat!

Nevermind at least I still got it! ;D

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=