• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

The forum and its posts will remain visible as a resource for a long time to come.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

ford 302 to renault transaxle

Started by bogwoppit racing, 05, July, 2010, 10:00:51 PM

Previous topic - Next topic

bogwoppit racing

hi every one i am finally coming to the end of my build of my mclaren m6 ,i am using a ford 302 with adapter plate to a renault 25 v6 transaxle ,it uses a ford v6 flywheel that has been adapted to fit the 302 with a renault 21 spline clutch plate and a ford v6 pressure plate .  with the standard renault clutch arm and release bearing which are operated by a slave bolted to the top of the bellhousing . the problem is that on my first test drive just to check every thing worked the clutch engaged and a horrible screaching noise come from the bellhousing and the clutch failed to work correctly.  so i have taken the transaxle out and the release bearing has broken into several pieces and it has scored a line into the centre of the pressure plate has any one got any ideas as i am flumoxed  yours hope fully dean

'The Gaffer'

Glad you are making progress there.

Sorry I cant offer any great mechanical advice, but could it be possible that the bearing was defective in the first place?

Maybe someone more mechanically minded may help?

bogwoppit racing

cheers for taking the time to respond all the parts used are new ,but i was maybe thinking if the master cylinder i am using is giving the slave to much push so it is just destroying the release bearing  ,but i just dont know !!

Hairy Santa

Hi
Take a few pictures of the problem and post them on here, and state again exactly how this happened ,
we may be able to diagnose what is going wrong

sounds like to much pressure - between release bearing to cover plate at the moment, was there any play there before you put the slave cylinder in place ?

Pete


bogwoppit racing

i spoke to chris cole today who seamed to think that the renault release bearing which is mostly plastic is,nt really up to the job and he sells steal ones that are much stronger so i have ordered one and hopefully this will do the job . iam also going to check how far the master pushes the slave and when it has reached the point that it has engaged far enough i will put a stop on the pedal .  any further input will always be greatly recieved though many thanks dean

Alfa Ric

Check the travel of the clutch bearing it can be the case that the slave cylinder is smashing it against the pressure plate

bogwoppit racing

should the clutch bearing constantly run on the pressure plate or should there be a gap ? and how far does the bearing need to move on the pressure plate to make the clutch work? please excuse my ignorance but i am still learnig, many thanks

Alfa Ric

#7
Well the only way is to compare the travel of the original bearing with the one you have now.
Some bearing are in fact attached to the pressure plate and some push the plate and not pull it.
Hope it helps

Ric

bogwoppit racing

i hav'nt got the new one yet as the man i am getting it off is going to le mans classic race today (lucky bugger) , but the bearing is attatched to the arm and slides forward to make contact with the pressure plate . the original one lasted about half a mile then made some horrible noises at which point i thought it was dead !!!! . i would put some pictures on but the only damage is some light scarring to the pressure plate and a bearing in four pieces .

Alfa Ric

I know is not easy to measure the travel of the clutch bearing with the gearbox in place...
Why don't you try (with the help of someone) to adjust the slave cylinder that you bolted to the bell housing ?
I know this is only a idea but what do you have to lose ?

Ric


Quarrycars

There are 2 types of clutch slave cyl, one is the short travel type where the piston stops in the released position and the clearance is adjustable.  The clearance has to be checked regularly as it reduces as the clutch wears.
The second type has a long travel slave with no back stop, a light spring keeps the release bearing in contact with the cover assy, as the clutch wears the piston moves further back into the cyl making it self adjusting.  Most clutches now are the second type.
If you have the second type check that you have plenty of travel by pushing the piston back into the cyl when it is all assembled.  The best way to check release is to put it in gear and jack up a rear wheel, have someone slowly press the pedal until you can turn the wheel then adjust the pedal stop to prevent overtravel.
Hope this makes some kind of sense! JT

bogwoppit racing

thank you all for your input , i will be having a good look at it next week but cant at the moment as i am running a campsite for the international air tatoo at raf fairford . if any one from the forum is looking for camping i am situated opposite the old spotted cow at marston meysey and wil be happy to do a reduced rate for the clubs members just mention bogwoppit racing to me when you turn up then i will know you are part of the club .   hope the weather improves   dean

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=