• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

The forum and its posts will remain visible as a resource for a long time to come.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Changing engine mounts

Started by Grin-a-lot, 02, August, 2010, 07:25:46 PM

Previous topic - Next topic

Grin-a-lot

I need to replace the engine mounts on the crossflow in my Westfield.  It rocks like a b*gger on the current mounts causing the exhaust manifold tomtouch the chassis.

I've never done this before and i'm wondering how easy it is, how much it'll cost and how long it'll take?

Can it be done without lifting the engine out or without any specialist tools?

Are there any guides on t'interweb or would anyone be interested in helping?

I don't want to keep taking it to my mechanic but I'm not sure where to start!

'The Gaffer'

I think you will have to get an engine hoist and lift the engine to change the mounts.

The engine dosent need to come out, just lifted enough to remove the mounts, you may have to loosen the gearbox mounts and maybe exhaust also to allow enough upward movement.

Unless you have the equipment, then I'm afraid its a trip to your mechanic. Maybe someone can lend a hand but I'm far to busy on another project right now.

Good luck. Its not really a big job :)

YellaBelly

As Phil said, not really a big job. If you don't have access to an engine hoist, you can use a trolley jack to lift the weight off the mounts (will only need to come up a couple of inches or so). Then you can change them with the engine still in the car. You might have to loosen/remove the exhaust downpipes or disconnect the manifold from the head but you should be OK I would think.

HTH.

JB

David H

If you call Westfield or look on the westfield forum (WSCC) you will find info on identifying engine mount types. There are different mounts depending on how stiff you want them, mostly available from ford for just a few pounds. I upgraded mine to stop engine rock a couple of years ago. Jack under sump to take weight and undo the bolts etc.

This will help with throttle reponse a little too.

Grin-a-lot

Cheers guys, i'm going to have a go at this myself.  I called Westfield who have the circular mounts in stock but there is a chance that mine are the rectangular mounts which are harder to come by apparently.

Will check which mine are when I get home, order them and do it myself I think.  All part of the learning curve I guess and once i've got the engine jacked up a bit swapping the mounts can't be too hard.

Got a nice little "to do" list building up already!

Bulldog Bri

Just catching up on this one.

I changed the rubber mounts on the Merlin in under 30 min's very easy job.

I've also got 2 old crossflow mountings in the garage your welcome to if you still need some.

8)

David H

there you go. join the club of list makers...... i really do understand......


Grin-a-lot

Bulldog Bri:  Thanks for the offer, i'll post on here on Friday and let you know what type I need.  Westfield said that the rectangular ones are a bit harder to come by so fingers crossed i've got the circular ones fitted.

If I could collect them Fri/Sat/Sun then that'd be great, if you're going on the French Boules run then we could just catch up there I guess.  Like I said, i'll post here on Fri morning and hopefully we can sort something out.

David H:  Perhaps this is the start of my list reducing to zero - we shall see...

Cheers,

Daz

Bulldog Bri

I'll put them in the car for Saturday you can have a look at the Boules comp'  :)

8)

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=