• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

Due to 100's of daily spam registrations, new member applications have been disabled. Sorry.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Fitting Seats - How easy?

Started by Grin-a-lot, 10, August, 2010, 03:08:34 PM

Previous topic - Next topic

Grin-a-lot

I'm looking to change my seats in my westie SE; the ones that I have got are pretty much just cushions that have been jammed into position.  I'd also like something on rails that I can move (so that the missus can reach the pedals).

I spotted this on ebay...

http://cgi.ebay.co.uk/Westfield-car-seats-/270618376535?cmd=ViewItem&pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item3f021cb957

and wondered if they would be suitable and how easy they would be to fit.  Any thoughts?

Cheers,

Darren

Psymon

Not sure if they will fit, was urs a widebody version ? that those seats come from.


Cheers Si.

Richard

Fitting seats is fairly easy. The fiddle is getting them in the right place, runners raise the height so most tend to avoid them.

Fairly sure as you aren't a "W" then they will be too wide. Get your width measurements and then check places like europaspares(plenty of other places sell seats as well) to see which models fit to help you narrow (ha-ha) the choice to look out for.

foggy

Like you I am going to change my car a little bit. I am afer seats/steering wheel/wheels. Have been right through e-bay and there are loads to choose from. I you are going to fit runners, thats going to make you seat that much higher and you might have a lap full of steering wheel. What I am going to do, is wait for the Kit Car Show in Exeter in October, where you can see what you are buying. The majority of e-bay stuff is non returnable and if you are a little bit out on your measurements, they won't fit.I am hoping to get just a good deal at the show than I would on e-bay. Any way thats what I am going to do. 

Grin-a-lot

Cheers guys, runner will be bad then because the lap/steering wheel interface is pretty close already.  I like foggy's idea of going to the October show, that might make things a bit clearer if I can see them.  Looks like i'll be looking for something that mounts directly to the floor; the missus will just have to stretch for the pedals...

Richard

When you get round to fitting the seats, I tried a few different options to get the holes where I wanted them and I'm not sure if any were brilliant but the best was;

Make a cardboard template of the bottom of the seat wider than the bottom of the car
Put the bolts in the seat and then cut out the holes where bolts go
Insert seat into car but leave template on seat
Get seat into your preferred driving position and mark the floor where the front of the template is with pencil or something
Remove seat
Place template back onto floor without the seat, align with marking,  mark holes and drill away.

Do not forget if you don't have them to put a couple of drainage holes in while the seat is out.

David H

I have had runners on 2 pairs of seats in my Westy with no issues with steering wheel. It all depends on the runners and the seats. My Cobra 7s were ok but my newer  Tritons are on the floor even with runners. Your 1990 chassis may need bars welding to hold the runners if they it's not done already.

YellaBelly

I'm going to use runners for my Cobra Roadster seats, not sure what they are from but I've seen a few around on the web and forums. They add around 30mm so not too bad, and at least the missus can get to have a drive so keeps her happy ;)

paintman

How had a load of hassle with my new seats!

I put them in easy enough.... with runners on drivers side only but it raised the seat about an inch which brought the top of the windscreen in direct eye view!

I cut out half the seat padding which brought it down a bit but a week later my a** went through the base of the seat. :o :o

I had to repair and strengthen it and ended up taking the seat out plus the 15mm ply that was under it and replacing it with 4mm chequer plate.

Still not good.......

David H

You guys must be using pretty thick runners. My runners are around 15mm max.

David H

#10
Quote from: Sir Grin-a-lot on 10, August, 2010, 03:08:34 PM
I'm looking to change my seats in my westie SE; the ones that I have got are pretty much just cushions that have been jammed into position.  I'd also like something on rails that I can move (so that the missus can reach the pedals).

I spotted this on ebay...

http://cgi.ebay.co.uk/Westfield-car-seats-/270618376535?cmd=ViewItem&pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item3f021cb957

and wondered if they would be suitable and how easy they would be to fit.  Any thoughts?

Cheers,

Darren

Roger from this club has those seats in his Westfield and I can say without exception they are the most comfortable kit car seats I have sat in.

Check you have two flat 2 inch wide steel plates going from one side of each half of the cabin to the other, i.e from one hip to another. If they are there (under the carpet usually) you will have no problems fitting these seats especially as they are soft. Call Westfield to check as they are still a stock item and ask if they will fit in your car. They will ask you if you have a narrow or wide body. Let them know.

simples

Furore Phil

In my car there are two chassis rails that match exactly with the attachment points in the chair. I attached some 30mmx30mm right angle steel to the chair (vertical bolts) and then some more bolts at 90 degrees to them into the sides of the chassis rails (via rivnuts). This meant that the seat was only around 15mm above the top of the chassis rails.

If I ever need to adjust the seats, I just drill some more holes in the angle steel !

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=