• Welcome to Bristol Kit Car Club and Forum - BKCC.
 
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Westfield Haybusa Diff Ratio Advice??

Started by Westiebusa, 13, February, 2011, 10:21:29 PM

Previous topic - Next topic

Westiebusa

I'm running a hayabusa engine in my Westfield & trying to second guess what diff ratio i should be running, i use the car mainly for Hill Climbs & Sprints, when i dropped the engine in i happened to have a 4:4 (english)LSD in it, Well that was fun on the first road run, wheel spinning through to 6th  :o it was like driving on ice lol, so i dropped a 3:54 in it but that calmed it down to much, now i know the lads who run Fireblade engines in thier cars run the 3:9's but they need to rev to get the power, but the Busa has good torque, so i've plumbed for the 3:7 which i've fitted but not had a chance to try it, but to be honest driving it on the road is nothing like driving it in competition!! so i thought i'd put it out here to see what peoples experience/thoughts are?  :-\
Adrian

'The Gaffer'

I always ran a 3.62 in my blade, which to me anyway, seemed to give me the best of both worlds being primarily a road car and secondly a track car.

Ratios are so personal, not to mention wheel and tyre sizes which make so much of a difference to overall engine to road ratio.

Hope your new ratio works out :)

Daley Down Under


Adrian,

I'm running a 3:14 in my supercharged ZZR1400.  Works really well on track and wouldn't want to go shorter for sprints/hillclimbs.  I'm surprised that 3.54 seems too long.

Adrian

peetee

I'm runing a 3.62 LSD in my fireblade powered MAC#1. It is possibly a bit too short? and I may need to go to 3.20? But I'm going to give it a try on the track first to see? With it revving to 11,000 I may just have enough top end?

Westiebusa

#4
 :D Thanks for the replies lads, forgot to say i run 13" with 60 profile, when it comes to sprints & hillclimbs top end is usually un-important, all the Blade boys i ran with ran with 3:9's where as it seems non of you go anywhere near that kind of ratio, there is only 1 Sprint i do that has a 1/4 mile straight & every body is usually on the rev limiter in top by the end! I have also driven a Hayabusa powered Pilbeam with the quaife diff unit which comes with 3:7 ratio & i only managed to get near the top end of 5th on the 1/4 mile!! But that kept the car calm(less wheelspin) through tight twisty bits without compromising acceleration as the Busa has loads of torque, i took class records @ 2 tracks with the pilbeam one by 4 seconds, but thats on slicks & a totally different breed of car, thats why i have opted for the 3:7, seems like a suck & see situation, just have to take all 5 diffs i got!! lol  :-\ ;D

Westiebusa

Quote from: MarlboroCar on 14, February, 2011, 08:53:46 AM

Adrian,

I'm running a 3:14 in my supercharged ZZR1400.  Works really well on track and wouldn't want to go shorter for sprints/hillclimbs.  I'm surprised that 3.54 seems too long.

Adrian
Jesus that must be a bl**dy quick beast!!! :o

tony.g

#6
I,ve got a Blade engine, 3.54 diff and 185 60 13 tyres.
I did a track day at the weekend and it definatly needs a different diff because i was on the rev limmiter half way down the straight. It was a very long straight at  Bedford.
I live round the corner from the guy that developed the Fireblade Caterham (James Whiting) and he told me the best diff for track work in my car is a 3.00, which means changing my English axle for an Ital one .
I am going to see him at the weekend and question him on it again.

Daley Down Under

Quote from: Westiebusa on 15, February, 2011, 08:40:45 PM
Quote from: MarlboroCar on 14, February, 2011, 08:53:46 AM

Adrian,

I'm running a 3:14 in my supercharged ZZR1400.  Works really well on track and wouldn't want to go shorter for sprints/hillclimbs.  I'm surprised that 3.54 seems too long.

Adrian
Jesus that must be a bl**dy quick beast!!! :o

Adrian,

Not quick enough - only 1 second quicker round Combe than my old Megablade - but I'm working on it!!  Did manage 144mph down the Hangar Straight at Silverstone last year (into a headwind).  Incidentally, Megablade ran a 3.1:1 Freelander diff and 60 profile on 13inch rims which was ideal for trackdays and the Sprints I did (no hillclimbs though). 

Adrian

Westiebusa

Now i'm totally unsure!! :-\ I think all that i can do is go with what feels right for the first meeting, i just want to be on the pace as i've moved up a class this year with the new Busa power & its very competetive i'll be up against 300bhp Red Tops etc, and to stand a chance of finishing in the top 3 of the Championship you need to be on the pace from the word go! Can anyone suggest a circuit/airfield track that is comparable to a sprint circuit i.e short straights & lots of twisty bits?? :D

Daley Down Under


Adrian,

WSCC Speed Championship use Llandow for Sprints (which is tight and twisty) and the circuit may be organising a car track day before Easter (prior to our day in May - check their website.  As for airfields, Abingdon (Motorsport Events) is probably the most realistic and they use it every month and its not too far away.  They used Colerne (another Sprint venue) until this year but new surface has put pay to that.

Adrian

Westiebusa

Quote from: MarlboroCar on 16, February, 2011, 11:19:13 AM

Adrian,

WSCC Speed Championship use Llandow for Sprints (which is tight and twisty) and the circuit may be organising a car track day before Easter (prior to our day in May - check their website.  As for airfields, Abingdon (Motorsport Events) is probably the most realistic and they use it every month and its not too far away.  They used Colerne (another Sprint venue) until this year but new surface has put pay to that.

Adrian
Thank you will look into that straight away, be good to give the car a shake down as i've only driven it a couple of times on the country lanes where i live since converting it from crossflow, so will need to see what falls off  :o also suspension is set up for crossflow weight!! Not done much to engine, just swopped out exhaust cam for another inlet cam, converted the fuel rail from factory dead head system to flow through with fuel reg (did the rail myself @ a cost of £7 :)) so now system is Tank>Pre-filter>Pump>Fuel Rail>regulator>Tank, fitted power commander & changed to manual timing chain adjuster. Will run this set up for first season to iron out any bugs, i've started collecting parts to build a 1507cc motor for next step ;D Once again thanks for the info!!

Daley Down Under

Quote from: Westiebusa on 16, February, 2011, 12:33:33 PM
Quote from: MarlboroCar on 16, February, 2011, 11:19:13 AM

Adrian,

WSCC Speed Championship use Llandow for Sprints (which is tight and twisty) and the circuit may be organising a car track day before Easter (prior to our day in May - check their website.  As for airfields, Abingdon (Motorsport Events) is probably the most realistic and they use it every month and its not too far away.  They used Colerne (another Sprint venue) until this year but new surface has put pay to that.

Adrian
Thank you will look into that straight away, be good to give the car a shake down as i've only driven it a couple of times on the country lanes where i live since converting it from crossflow, so will need to see what falls off  :o also suspension is set up for crossflow weight!! Not done much to engine, just swopped out exhaust cam for another inlet cam, converted the fuel rail from factory dead head system to flow through with fuel reg (did the rail myself @ a cost of £7 :)) so now system is Tank>Pre-filter>Pump>Fuel Rail>regulator>Tank, fitted power commander & changed to manual timing chain adjuster. Will run this set up for first season to iron out any bugs, i've started collecting parts to build a 1507cc motor for next step ;D Once again thanks for the info!!

Not done much to engine - doesn't sound like that to me  :D

1500 busa will be awesome - radical seem to make them go well

Westiebusa

#12
That's quite mild for me, i almost enjoy the engine build side as much as driving, like to see what i can get out of the engine myself (reads to tight to pay anyone else ;D) built my All Steel 1800(84mm Crank +60 Pistons) Crossflow & got 182bhp/160lb/ft on Carbs, Ported & gas flowed the head myself etc....
I've just bought a crank of ebay which believe it or not it's cheaper for me to send to USA for exchange for 5mm Stroker crank with Corrillo Rods than i can buy just the crank in this country, i can also get 84mm JE Pistons for £360 inc delivery!! :o
Just a side ? how do you insert image in thread? Obviously computers my weak point!! ;D

Daley Down Under

I'm no expert - I upload my images to Photobucket and then insert the hyperlink.

Westiebusa

Quote from: tony.g on 15, February, 2011, 09:16:02 PM
I,ve got a Blade engine, 3.54 diff and 185 60 13 tyres.
I did a track day at the weekend and it definatly needs a different diff because i was on the rev limmiter half way down the straight. It was a very long straight at  Bedford.
I live round the corner from the guy that developed the Fireblade Caterham (James Whiting) and he told me the best diff for track work in my car is a 3.00, which means changing my English axle for an Ital one .
I am going to see him at the weekend and question him on it again.
Why isn't the Ford Atlas an option??, you can get them with 3:09 Ratio, no probs with wheel stud pattern, very similar fitment to what you have already & have been proven to be strong in rally cars, parts readily available, Dixie has a complete axle for sale ;D

tony.g

I've got no idea,
everybody always used the Ital axle.
Has anyone got any idea or measurements and photos?

Westiebusa

#16
Dixie (Mark) has got a complete axle, give him a PM as he wants to sell it so i'm sure he would give you the measurements & pics, i would of thought as long as the width is ok it would be quite a straight forward swop!! ;D

Look here for pic, i believe you can get different width ones?
http://cgi.ebay.co.uk/52-Atlas-axle-capri-/280632090827?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item4156f9e0cb

Or this one, says fits Escort so can't be a lot different than yours??
http://cgi.ebay.co.uk/Ford-atlas-axle-mk1-and-mk2-Escort-/300528578589?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item45f8e6301d

tony.g

Just done a bit of homework on the  width,the escort English axle is 48". MK 1 Capri Atlas is 50" which i think will fit.

I will hace to get the tape measure and trolley jack out at the weekend!


Quote from: Westiebusa on 23, February, 2011, 08:53:27 PM
Dixie (Mark) has got a complete axle, give him a PM as he wants to sell it so i'm sure he would give you the measurements & pics, i would of thought as long as the width is ok it would be quite a straight forward swop!! ;D

Look here for pic, i believe you can get different width ones?
http://cgi.ebay.co.uk/52-Atlas-axle-capri-/280632090827?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item4156f9e0cb

Or this one, says fits Escort so can't be a lot different than yours??
http://cgi.ebay.co.uk/Ford-atlas-axle-mk1-and-mk2-Escort-/300528578589?pt=UK_CarsParts_Vehicles_CarParts_SM&hash=item45f8e6301d

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=