• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

A big thanks to all members past and present for making the club viable for so long.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Westy Megablade - Cush Drive and Sump Baffles

Started by madmarkymark, 19, July, 2011, 11:09:44 PM

Previous topic - Next topic

madmarkymark

Hi,

Has anyone fitted a cush drive to their BEC?  What differences do you feel?  Who fitted it (shortened prop etc)?  Any info would be appreciated.

I was at the Keevil Track Day a couple of weeks ago and my Westy was flying.  However, I am concerned about oil surge.  Is it an issue on the Blade engines?  Do I need to look at baffling the sump?

Thanks for any contributions.  ???

Madmarkymark

TimC

Ring Andy at AB Performance on 01449 736633 - THE Fireblade BEC guru.

tony.g

I have recently fitted a sump baffle to my 919 blade engine, not that i had any problems but it's put my mind at ease.
I have also fitted a dynojet kit which i got from Andy Bates (can't wait until my next trackday).
I don't have a cush drive but A B Performance can make you a propshaft with one built into it.

As TimC said, give him a ring, he is very willing helpful


paintman

I would definitely fit baffles......Stupott blew his engine recently on his MK and that was the reason. ::)

     Tony

tony.g

If you are feeling rich, A B do a billet sump. :D

Newton

I went for the billet sump option when Andy Bates supplied my replacement engine.  He occassionally has a second hand one he'll do a deal on but you still need to plan on £200 ish.  You also need to listen to his instructions about oil level as you need to overfill.

Andy also does a cush drive I seem to recall on his site.  Just depends how well you get on with Bike engine in a car if you can be smooth then the loads you apply however if you're not you end up with very high instantaneous torque being imposed on the drive train.  Bikes have a cush drive system incorporated in the rear wheel.

Rob

Daley Down Under

Mark,

Yours is a carb engined blade right?

If so, all you need is the Westfield baffle plate which should already be installed. You can check as it is visible between the crankcase and the sump (two gaskets).

You only need an AB billet sump with injection blades (929 or 954)

As for the Cush drive, the resilient props do a good job of reducing the drive clunking. Never going to be smooth though - after all it's a BEC. Drive and enjoy.


Adrian

tony.g

AB always fit the billet sump on any carbed Blade engines they sell.
I was told somewhere else that you don't need baffles or billet sump unless you use slicks.
The billet sump is also shorter giving you more clearance.
If you have got baffles as Adrian says, I would leave it at that.

Tony

peetee

Andy Bates at AB says you must fit at least a baffle plate for all carb engine blade engines and a full billet sump for all injection blades (929/954) if you are doing any track days, not just if you are using slicks. Standard tyres/set up can generate more than enough oil surge to cause irreparable engine damage. The AB billet sump is a lovely bit of kit and an additional benefit as Tony says is much better ground clearance.

'The Gaffer'

Good advise from all. My old Blade was built by AB and had a nice sump. Always over fill as well.

I had a resilient prop custom made for my Toniq, but to be honest the car was just as clanky with it.

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=