• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

The forum and its posts will remain visible as a resource for a long time to come.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Engine rebore?!?

Started by Grin-a-lot, 22, August, 2010, 06:33:57 PM

Previous topic - Next topic

Grin-a-lot

It appears as though my crossflow is suffering from a pressurised sump.  It seems to have deposited about a pint of oil in the catch tank over just 100 miles.  I'm planning on getting it compression tested this week but am assuming the worst.

Has anyone had an engine rebored, is there anyone you'd recommend and, quite importantly, how much roughly is this going to set me back! I wouldn't have a clue how much I should budget for this!


foggy

Sorry to hear that, it seemed to go well this afternoon. Tomorrow as you know I am going to look at vynil graphics, next door to them is a company that specialises in engine rebuilds, it so just happens that I know the owner as my son served part of his mechanical apprentiship with him. I will pop in there and have a word. Yours is a 1700 cross flow? I will let you know what I find out.

foggy

Just had a quick thought, your engine breather would'nt be blocked would it?  I seemed to remember that some one else had the same problem .But I expecct that some of the boys in the club might know a bit more about this than me.  So it might not be all doom and gloom.

Grin-a-lot

The breather leads to the catch tank and thats certainly allowing a fair amount of oil into the tank so i'm sure that's clear and open to atmosphere.

Mine is the 1700 crossflow and what has me concerned is the amount of oil that wound up in the tank in a relatively short space of time.

The oil filler cap does have a pinhole in it (I assume to allow it to breath) but not sure that is doing anything.

I removed the cap with the engine running and it is smoking a bit which i figured isn't a good sign.

I'd be interested to hear what this place you are going to has to say as well.  Good luck with the MOT and wrapping!

David H

This is a large conversation but I am happy to have it with you. I have had the same problem from one of my old engines in my Westy. I tried a lot of things but it was a cracked piston that was letting by. I'm not saying that is the problem with yours though.

Is this a new problem?

I'm quite happy to go throught this with you on the phone as I am not able to be on the pc much at the mo. I've sent you a PM with my number on it. By the way, my car has almost the same reg as you and is the same colour. Small world.

Dave

Grin-a-lot

Cheers Dave, I'll be in touch Monday.

Interesting point about your piston rings though, the engine is only about 2000 miles old so perhaps a damaged ring is more likely than a worn engine.

I'll bend you ear tomorrow then! Enjoy the rest of your weekend!

foggy

Went down to see Steve at Price Bros Engineering,he told me being your car is a 1700 and as far as he can find out,they did'nt make a 1700,but a 1600, so it might have already been re-bored. As for what pistons they put in it,the number is on the inside of the piston,to say whether its oversized or standard and to  find out if the pistons are still available. He says another option is re-sleeveing it.I have sent you a pm with his phone number,so you can talk to him direct.Of course it might not be so bad as this,he would just want the engine,not the car,but I think you will have to look into this more, before you start spending hard earnt  on it.

foggy

What was the outcome from the engine problems (oil leak)

Grin-a-lot

Oil leak fixed so all good there.  I can actally park my car on people's driveways now without recreating the BP Gulf of Mexico incident.  As far as the heavy breathing goes, there seemed to be a short and sharp dump of oil into the catch tank and it's settled down again.  I'm going to keep an eye on it over Autumn/Winter.  If the engine is a bit ropey then I'll investigate options around easter time.  Perhaps its hinting at a Zetec upgrade..!

bernih

hi,

i've run crossflows for years and over 1650's need BIG breathers unless they chuck out their oil.

i'd recommend a breather pipe off the block of at least 25mm dia (mine is 42mm) that needs to be routed above the highest point of the engine before dropping into the catch tank.  this haleps ensure that any pil drains back into the sump rather than spat out into the catch tank.

i've got photos but i'm new on here so haven't worked out whether i can post them.

Bernie

'The Gaffer'

Quote from: bernih on 09, September, 2010, 02:38:52 PM
i've got photos but i'm new on here so haven't worked out whether i can post them.

Bernie

Hi Bernie.

You are more than welcome to add pics to your posts and the gallery.

In posts just cklick 'Add image to post' above the text input window.

If you have 5 mins, please tell us a little about yourself in the introduce yourself section of the club forum :)

bernih

hi,

here's a picture of my old X-flow from a few years back but i still run the same breather system.  the bit you can't see from the pic is that i still use the original flame arrester box fitted into the block with a steel stub welded into it to fit the braided hose onto.  again this helps stop oil getting out of the engine rather than just stick a hose into the hole on the block.

there's also a small breather from the rocker cover into the air filter body and the pinhole on the filler cap is sealed with silicone.

apologies for the high quality catch tank but it had to be 2 litres - and i Halfords anti-freeze bottle was in the garage and free.



if the engine's only 2000 miles old i'd go for breathers first - especially as it only does it sometimes - and it's a cheap option that doesn't involve stripping the engine.

Bernie

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=