• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

A big thanks to all members past and present for making the club viable for so long.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Spark plugs

Started by foggy, 04, September, 2010, 04:27:01 PM

Previous topic - Next topic

foggy

Easy  job-change the spark plugs---wrong!! Managed to get 3 out,4th one won't move.Ran the engine to get it hot to see if that would loosen it off a bit,but no-still won't move. Don't want to put any more force on it,the engine still runs purfect at the moment,got a horrible feeling the last owner might have cross threaded it. I will leave it for the minute.I suppose if I can't get it out, its the head off I suppose for hele coil.Any ideals (spark plug type with no washers)

Mark G

You could try leaving some penetrating oil in the plug hole overnight and try removing the plug tomorrow.  I wouldn't remove the head until you know that the thread is knackered.

Good luck

Quarrycars

Good idea with the penatrating oil, there is a chance it's not crossthreaded, if it wasn't tightened properly last time combustion blowby may have gummed up the threads.  Do you have taper seat plugs in an alloy head?

foggy

As far as I know, its not a ali head.The spark plugs are slightly tapered above the thread. I have replaced them with exactly what I took out. NGK APR6FS.2 LITRE Pintoe, rebored to 2.1.

Quarrycars

I think that is an 18mm taper seat, they can get very tight due to the large seat area.  It's a pretty robust thread, if it is tight all the way out you will need to clean the thread and seat, I have a 18mm thread cleaner or you can make one by grinding flutes on an old plug.
BTW don't be tempted to put oil or grease on the threads on the new plugs, it will bake on and make it hard to get them out next time!

bernih

hi,

in my experience you will just have to put a lot of force on to get it loose - they're much more difficult to get tightened just right than ones with washers, especially on Pintos.

use a good quality spark plug socket with as short an extension as you can get away with, then a T-bar on top.  put a 600mm tube on each end of the T-bar so that you're only turning not pulling and gradually try to turn.  if it wants to go it'll `crack' quite easy, if you're getting a sweat on even with the two bars then leave it until you take the head off.

good luck,

Bernie

paintman

Surely it will be even harder to undo it with the head off. 

If I was doing it I would get a good box spanner, put a bar through it. Then get a steel tube  (I use the one off my trolley jack)  which will fit snugly over the bar and with that ammount of leverage it should come undone. ;)

bernih

Quote from: paintman on 09, September, 2010, 07:57:34 PM
Surely it will be even harder to undo it with the head off. 

yeah, but if it won't come undone with a BIG lever on each end of a bar then you need to know why, and looking inside might tell you.  once the head is off you can knock out the centre of the plug, drill out to weaken it and then i've found it will give up the fight.

Bernie

'The Gaffer'

I've actually snapped a plug by putting too much pressure on :o

Never again. Good advice Bernie.

paintman

So if you snap the plug then you can take the head off and drill it out. ;D

'The Gaffer'

Quote from: paintman on 09, September, 2010, 11:22:56 PM
So if you snap the plug then you can take the head off and drill it out. ;D

Yes you are right but I could have just as easily scrapped the head by being over jealous. If things are too tight there is a reason ;)

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=