• Welcome to Bristol Kit Car Club and Forum - BKCC.
 

News:

A big thanks to all members past and present for making the club viable for so long.

Main Menu
AIB BKCC Kit Car Insurance
Discounts For Club Members

+-Member Login or Register

Welcome, Guest.
Please login or register.
 
 
 
Forgot your password?

Intake Manifold bolts - how tight?

Started by Grin-a-lot, 10, September, 2010, 10:18:26 AM

Previous topic - Next topic

Grin-a-lot

In my quest to stop my car backfiring i nipped up all the bolts on the intake manifold because I thought they were quite loose (and I thought that extra air sneaking in would mess up the air/fuel ratio etc.

Someone told me recently that they can be a bit loose and now that i've tightened them i can't get idle to drop below about 1600 so i wonder whether there's some truth in it.

So, roughly how tight should my intake manifold bolts be: finger tight/hanging off them tight etc?

Cheers!

'The Gaffer'

#1
I'm not a mechanic but I srongly suggest you find the correct torque settings for those nuts, buy or borrow a torque wrench and get them tight.

Probably a good idea to replace the gasket too.

No nuts that I can think of on an engine including manifolds should be just fingertight :o

Sounds like your setup was done with a loose manifold, time to tighten it up and get the engine set up again me thinks.

Grin-a-lot

The arguement was that you don't want your carbs rigidly mounted to the engine to limit the vibration from the rocking engine damaging the union with the carbs.

My theory is that if you want a seal then it needs to be a fairly tight union for it to work.  A couple of mm of flex may well upset that.

What i don't understand is that now its tightened; the mixture screws are towards the lean end of the spectrum and no matter what I do with them I can't get the idle speed to drop below 1600rpm.

I've got it booked in to be tuned and balanced again 24/9 but trying to figure it out myself; its intriguing...


'The Gaffer'

Maybe a stupid suggestion but does the throttle cable / linkage close fully with a tiny bit of cable slack. Perhaps you could try adjusting that, usually a screw that makes physical contact to the linkage.

Maybe the cable is sticking?

Camber Dave

In the old days when I did a lot of Twin Cam Loti with Webers or Dellorto's we had this problem.

The carbs are mounted on flexible mountings; originally double wound (Thackery) spring washers. Later these were replaced with more durable rubber spacers between steel washers. Between the carb base and the head or manifold was a pair of 'o' rings either side of a grooved spacer either alloy or later plastic.

As previously posted this was to allow the carbs to be insulated from the engine vibration. The vibration shook up the fuel in the float chamber causing air bubbles which upset the smooth running of the engine.

Often the 'O' rings perished and allowed air to leak into the manifold weakening the mixture. As you did the quick fix was to slightly tighten the nuts but the best thing was to replace the 8 rubber rings  and broken washers.

Then refit the carbs. Tighten the nuts so that each washer just stops rattling loose. then tighten them all again about 2 complete turns for a metric thread or 3 for a UNF (fine) thread.
Reset the balance (use a length of heater hose and listen to the inlet suck on each trumpet - it is as good as any balancer!) and retune them.

The mixture screws are the vertical ones with springs on them at the engine side of the carb body. Wind each screw out 1 turn from the point where they are running now. Then tighten 1 screw at a time about a 12th of a turn (think clock face) until the engine revs rise a little. Next go to another screw and do that one. Do all four as quick as practical. Keep reducing the idle speed to as low as the engine will accept so you can hear the engine react to your adjustments.
You should manage this in about 10 minutes; any more and the spark plugs will start to foul up and a quick run up the road will settle things again.
On a correctly set engine 1/2 turn (1 Turn on a dellorto) of the mixture screw in either direction will 'switch off' that cylinder at idle.

The reason your idle went skywards was probably when the carbs were tightened you moved one carb relative to the other and so altered the balance setting.
This is reset with the screw in the connecting link (usually at about 45deg)
The vertical screw between the carbs moves both butterfly spindles to adjust the overall idle speed.

bernih

hi,

when you say the inlet manifold bolts i think you mean the ones holding the carb(s) onto the manifold, not the manifold onto the head.

can you give a bit more on what the engine and carbs are or advice could be completely wrong.

if it is the fitting of the carbs onto the manifold and it's twin Webers or Dellortos then you should have rubber bobbins with cap washers either end under each nut. 

I'd also guess you should have Misab rings between the carbs and the manifold - 2 per carb.

if you've bolted everything up tight then that's too tight.

i would suggest (because this is what i always do) that the way to do it is to evenly tighten each set of four nuts per carb until there's a clearance of 1mm between the faces of the cap washers.  this leaves the carbs free to move but definitely tight enough to avoid air leaks.

BUT, now that you've wound everything down hard due to `spitting-back' you need to have a look at all the bits i.e. take off the carbs and check the Misab rings and rubber bobbins.  if you still have the separate O-rings between the carb & manifold then get rid and buy Misabs - they cost more but last so much longer.

same goes for Thackeray washers versus rubber bobbins.  if you've already got bobbins, buy some new ones.

then when you've got the carbs mounted properly look for what's actually causing the spitting back.

i live in South Bristol if you're anywhere close and don't mind having a look at it for you one night if you like (for free, don't worry).

Bernie

Grin-a-lot

Thanks for the replies;

You are right about the bolts, the ones that I was talking about are the ones that mount the carbs to the manifold (8 in number).

The engine is a 1700 crossflow with twin Weber 40s on it (DCOE) and it is about 2000 miles (7 years) old. 

As far as the nuts go; I've got a Thackeray washer under each nut and that's it.  I assumed a nylock might've been good to stop movement of the nut but not on my car!

I don't know what the sealing arrangement between the carbs and the inlet is as I've not had them off yet.  However there is a metal gasket type thing sandwiched between black rubber seals (as far as I can make out).  I don't think that they are individual o-seals but i've not really looked hard at them.

Since my post above, I've slackened the nuts off a bit (1.5 turns each) and that dropped the idle speed down to a more reasonable level.  I've also tweaked the air/fuel screws to make the carbs run leaner; this has stopped the popping and backfiring from the exhaust and inlet.

I suspect now that the car is running safely but not at its optimum.  I also sealed the exhaust at every join that I could find that might let air in.  I've put carb cleaner through the carbs but not serviced the carbs at all – I was hoping that they wouldn't require it since they're not that old.

As a bit of an aside; am I right in saying that I can remove the jets and blow them through with compressed air without causing any changes to anything else?  I thought that prior to having them tuned it would be good to ensure that they are not clogged with any debris etc.

bernih


OK, if you've got Thackeray washers which are 7 years old i'd change them anyway.  the metal gasket with the rubber ring sounds like a Misab ring - again i'd be tempted to change them

here's a couple of pics
Misab Ring

Bobbin mounting kit


personally i wouldn't advise blowing the jets through with compressed air.  you can look through all of the removable ones easily enough to see if there's any rubbish in there.  the idle & man jet carriers are accessible from under the twiddly round cover on top, but there are a load of other jets and drillings in the carbs that you can't get to without a full stripdown.  use exactly the right size screwdriver for the slot in the brass jet carriers, they damage real easy.

so just back to the start, why are focusing on the carbs anyway, has something suddenly changed that you reckon is down to them?

Bernie

Grin-a-lot

Yeah I had them tuned about 2 weeks after buying the car but is started backfiring really badly afterwards (blue flames and all sorts); this only seemed to happen when the engine was shutdown.  I also started to get a significant amount of pinking as well and a cracking/popping noise coming from the vicinity of the carbs.  From conversations on here and at meets, I came to the conclusion that the carbs were not tuned correctly.

I had the timing corrected with a timing light but the backfiring continued.  That is the point that I tightened the nuts and found that the idle speed went mad etc (hence the posts above).

Just prior to that I repacked the silencer with wire wool and the white blanket stuff (just because it was loud) but then sealed all the joins and rivet holes etc.  I wondered whether the backfiring was due to that so attempted to eliminate the chance of any air entering the exhaust system.

Ignition leads and plugs have all been changed as well.

As far as the jets go; I was thinking of going for the removable ones as I don't really trust myself to strip the carbs to get to the remainder.  I did stick a can of cleaner through the carbs though so hopefully that's dislodged the worst of what was in there.

Powered by EzPortal
Great value Kit Car insurance. Dont forget to mention the BKCC
Discounted insurance for our members.</a></center>
			</div><!-- #main_content_section -->
		</div><!-- #content_section -->
	</div><!-- #wrapper -->
</div><!-- #footerfix -->
	<div id=